The Game Boy Advance Overclocker Flex by robot_retro replaces the original GBA crystal and gives you full control over your GBA's clock speed – from a relaxed 30 % all the way up to 170 % of the base clock.
- 6 speed settings: 30 %, 50 %, 75 %, 130 %, 150 %, 170 % of base clock
- Largely wire-free flex installation (optional LED wire only)
- Ultra-low power draw <15 mA
- Accurate base clock: 4.194 MHz, >0.01 % precise
- DIY install requires soldering skills – install at your own risk
Game Boy Advance Overclocker Flex – Full Control Over Your GBA Clock Speed
Want to speed-breed Pokémon faster, eliminate slowdowns in Castlevania, or just see what a GBA feels like at 170 % clock speed? The Overclocker Flex by robot_retro makes it happen. It replaces the original crystal on the GBA mainboard and gives you access to six different clock speeds at the press of a button – developed in collaboration with RJS FPGA.
Features at a Glance
- 6 clock speed settings: 30 %, 50 %, 75 % (underclock) and 130 %, 150 %, 170 % (overclock) of the original 4.194 MHz base clock
- Change speed: Start + Up = faster | Start + Right = slower
- Flex PCB design: No manual wiring required (exception: optional LED indicator wire to test point DL2A)
- LED feedback (optional): Power LED blinks faster when overclocked, slower when underclocked – base clock = solid green
- Ultra-low power draw: <15 mA (measured with Nordic Power Profiler Kit II)
- Highly accurate base clock: 4.194 MHz at >0.01 % accuracy – no difference to the original crystal at stock speeds
Maximum Speed & IPS Compatibility
Depending on your installed display, you may need to limit the maximum speed via solder jumper to avoid screen glitches:
| Display | Max. Speed | Setting |
| Stock LCD / FunnyPlaying v2 / Hispeedido v2 (non-laminated) | 170 % | Default (no jumper) |
| Hispeedido Laminated v5 | 150 % | Bridge solder jumper S1 |
| FunnyPlaying 3.0" Laminated | 130 % | Bridge solder jumper S2 |
Installation – What to Expect
The install is comparatively straightforward for an overclocker mod, but not suitable for beginners without soldering experience. You will need at least basic soldering skills and ideally a hot air station to remove the original GBA crystal.
- Remove the original GBA crystal (hot air station recommended)
- Place the flex mod and solder 6 points (flux recommended)
- Optional: Run a wire to test point DL2A for the LED indicator
⚠ Note: This overclocker must be self-installed. We accept no liability for improper installation. If in doubt, please consult an experienced modder.
Strengths & Limitations
- ✅ No cable clutter thanks to flex PCB design
- ✅ Identical to the original crystal at stock speeds – zero drawback in everyday use
- ✅ Compatible with popular IPS mods (with correct speed limiting)
- ⚠ Not all games handle maximum overclocking – some may run unstably
- ⚠ Flash carts and reproduction cartridges only work at base clock speed – no overclocking possible
- ⚠ Installation requires soldering skills and hot air equipment
- Brand compatibility
- Nintendo
- WEEE registration number
- 23582226
Manufacturer
FDC Services Ltd (RobotRetro)
42 Shortheath Crest
GU9 8SB Farnham
United Kingdom
EU responsible person
OpenPandora GmbH
+49 841 1317733
Asternweg 5
Michael Mrozek
85080 Gaimersheim
Germany
chat
Comments (0)
Out-of-Stock
Enhance the audio quality of your GameBoy Advance with this amplifier upgrade kit, which includes a superior audio amplifier and a better 2W speaker.
€19.00
GBA SP Overclocker Flex Mod
In Stock
The Game Boy Advance SP Overclocker Flex by robot_retro replaces the original GBA SP crystal and puts you in full control of your console's clock speed – from a relaxed 30 % all the way up to 170 % of the base clock. Flex PCB design, minimal wiring, developed in collaboration with RJS FPGA.
6 speed settings: 30 %, 50 %, 75 %, 130 %, 150 %, 170 % of base clock
Control via Select + R (faster) / Select + L (slower)
Ultra-accurate base clock: 4.194 MHz ±0.01 % – indistinguishable from stock at base speed
Optional LED indicator (power LED blinks faster/slower depending on clock speed)
Ultra-low power draw (<15 mA)
Multicoloured wire included
6 speed settings: 30 %, 50 %, 75 %, 130 %, 150 %, 170 % of base clock
Control via Select + R (faster) / Select + L (slower)
Ultra-accurate base clock: 4.194 MHz ±0.01 % – indistinguishable from stock at base speed
Optional LED indicator (power LED blinks faster/slower depending on clock speed)
Ultra-low power draw (<15 mA)
Multicoloured wire included
€29.00
GBA SP Screen Kit (IPS)
In Stock
The RetroSix CleanScreen Kit (Laminated IPS) for the Game Boy Advance SP is the most refined display upgrade for Nintendo's iconic clamshell handheld – zero ghosting, zero tearing, zero flickering, with vivid colours and true-to-original image reproduction.
Fully laminated IPS display – no dust or smudges between glass and panel
Identical pixel size to the original GBA SP screen
OSD menu with brightness, colour modes, scanlines, pixel grid & True Motion
Ultra-low-power driver board – lowest power draw of any IPS kit on the market
No soldering required for the basic installation
Fully laminated IPS display – no dust or smudges between glass and panel
Identical pixel size to the original GBA SP screen
OSD menu with brightness, colour modes, scanlines, pixel grid & True Motion
Ultra-low-power driver board – lowest power draw of any IPS kit on the market
No soldering required for the basic installation
€95.00
Game Boy Advance CleanScreen Screen Kit (IPS)
Last items in stock
The RetroSix CleanScreen IPS Kit is the best display upgrade available for your Game Boy Advance – modern IPS panel, true-to-original colors, and zero compromises on retro feel.
Drop-in solution: no cutting or trimming of OEM shells required
Identical pixel size to the original display
True Color mode: color calibration matching the AGS-101 standard
Zero ghosting, tearing or flickering
Ultra-low power draw: lowest of all IPS kits on the market
Drop-in solution: no cutting or trimming of OEM shells required
Identical pixel size to the original display
True Color mode: color calibration matching the AGS-101 standard
Zero ghosting, tearing or flickering
Ultra-low power draw: lowest of all IPS kits on the market
€75.00
Gameboy Advance SP USBC-PD Mod
In Stock
You'd like to charge your GBA SP using a standard USB-C power supply? This mod replaces the custom Nintendo connector with a standard USB-C PD one.
€12.00
Gameboy Advance SP USBC Mod (with audio)
In Stock
You'd like to charge your GBA SP using a standard USB-C power supply? This mod replaces the custom Nintendo connector with a standard USB-C one, including Audio support.
€19.00
GameBoy Advance SP Conductive Pad Set
In Stock
Replacement conductive pad set for the GameBoy Advance SP – the go-to fix when buttons stop registering properly or feel unresponsive.Designed to fit the GameBoy Advance SP perfectly.Brings sluggish or unresponsive buttons and D-pad back to life.No soldering required – just a small screwdriver and a little patience.
€5.00
GameBoy Advance Screen Protector (Glass)
In Stock
Replace the scratched or cracked screen lens on your GameBoy Advance with a brand new scratch-resistant glass cover.Designed as a direct, precise fit replacement for the original GameBoy Advance screen lens.Made from scratch-resistant glass for a permanently clear view of your game.Perfect for retro gaming fans, modders, and tinkerers looking to restore their GBA.
€5.00
GBC Overclocker Flex Mod
In Stock
The Game Boy Color Overclocker Flex by robot_retro replaces the original GBC crystal and puts you in full control of your Game Boy Color's clock speed – from a relaxed 30 % all the way up to 170 % of the base clock. The flex PCB design eliminates almost all manual wiring.
6 speed settings: 30 %, 50 %, 75 %, 130 %, 150 %, 170 % of base clock
Button-combo control: Select + Up = faster, Select + Down = slower
Flex PCB design – no manual wiring required
Max speed configurable via solder jumper (170 % / 150 % / 130 %)
Works with flash carts; not compatible with OLED screens
6 speed settings: 30 %, 50 %, 75 %, 130 %, 150 %, 170 % of base clock
Button-combo control: Select + Up = faster, Select + Down = slower
Flex PCB design – no manual wiring required
Max speed configurable via solder jumper (170 % / 150 % / 130 %)
Works with flash carts; not compatible with OLED screens
€29.00
GBA SP Overclocker Flex Mod
In Stock
The Game Boy Advance SP Overclocker Flex by robot_retro replaces the original GBA SP crystal and puts you in full control of your console's clock speed – from a relaxed 30 % all the way up to 170 % of the base clock. Flex PCB design, minimal wiring, developed in collaboration with RJS FPGA.
6 speed settings: 30 %, 50 %, 75 %, 130 %, 150 %, 170 % of base clock
Control via Select + R (faster) / Select + L (slower)
Ultra-accurate base clock: 4.194 MHz ±0.01 % – indistinguishable from stock at base speed
Optional LED indicator (power LED blinks faster/slower depending on clock speed)
Ultra-low power draw (<15 mA)
Multicoloured wire included
6 speed settings: 30 %, 50 %, 75 %, 130 %, 150 %, 170 % of base clock
Control via Select + R (faster) / Select + L (slower)
Ultra-accurate base clock: 4.194 MHz ±0.01 % – indistinguishable from stock at base speed
Optional LED indicator (power LED blinks faster/slower depending on clock speed)
Ultra-low power draw (<15 mA)
Multicoloured wire included
€29.00
GameCube USB-C Power Supply
In Stock
A drop-in USB-C power supply replacement for your GameCube. Extremely reliable, supports all GameCube revisions and upgrades like PicoBoot or PixelFX.
€35.00
PlayStation 1 USB-C Power Supply
In Stock
A drop-in USB-C power supply replacement for your PlayStation 1. Extremely reliable, supports fans and the power LED can be set to different colors.
€49.00
Gameboy Original IPS Power Regulator Pro (Low Noise)
In Stock
The Game Boy Original IPS Power Regulator Pro (Low Noise) by Robot Retro is a direct solder-in replacement for the stock DMG-01 power supply – purpose-built for IPS screen mods. Note: Does not work with the original Game Boy screen.
~85% efficiency between 3.5V and 8V (with IPS screen + flash cart)
Noticeably reduced speaker hum thanks to high-quality aluminium capacitors
Low voltage cutoff protects your system from instability
Compatible with Game Boy DMG-01 (Original) only
~85% efficiency between 3.5V and 8V (with IPS screen + flash cart)
Noticeably reduced speaker hum thanks to high-quality aluminium capacitors
Low voltage cutoff protects your system from instability
Compatible with Game Boy DMG-01 (Original) only
€19.00
Installation of Saturn USB-C Replacement Power Supply (Kit included in the price)
Last items in stock
A replacement power supply for Dreamcast that allows you to use a standard 30W USB-C PD power supply. No need to do any soldering, just switch your old one with this.
€89.00
Saturn USB-C Replacement Power Supply
Last items in stock
A replacement power supply for the Sega Saturn that allows you to use a standard 30W USB-C PD power supply. No need to do any soldering, just switch your old one with this.
€59.00
Installation of Dreamcast USB-C Replacement Power Supply (Kit included in the price)
In Stock
A replacement power supply for Dreamcast that allows you to use a standard 30W USB-C PD power supply. No need to do any soldering, just switch your old one with this.
€89.00
Installation of the Gameboy Advance SP USBC Mod (with audio) (kit is included in the price)
In Stock
You'd like to charge your GBA SP using a standard USB-C power supply? This mod replaces the custom Nintendo connector with a standard USB-C one, including Audio support.
€45.00
Installation of the Gameboy Advance SP USBC-PD Mod (Kit is included in the price)
In Stock
You'd like to charge your GBA SP using a standard USB-C power supply? This mod replaces the custom Nintendo connector with a standard USB-C PD one.
€35.00
Gameboy Advance SP USBC-PD Mod
In Stock
You'd like to charge your GBA SP using a standard USB-C power supply? This mod replaces the custom Nintendo connector with a standard USB-C PD one.
€12.00
Gameboy Advance SP USBC Mod (with audio)
In Stock
You'd like to charge your GBA SP using a standard USB-C power supply? This mod replaces the custom Nintendo connector with a standard USB-C one, including Audio support.
€19.00





